Editorial Article

The Truck Tyre Has a Hard European Deadline of 1 April 2032, and the Test It Must Pass Has Not Been Written

Updated November 21, 2026

A truck tyre sold in Europe after 1 April 2032 will have to meet a legal limit on how fast it wears. That limit will be measured by a test method which, at the time of writing, has not been adopted. It is not a drafting oversight in a distant regulation; it is the stated position of the United Nations body that writes the rule.

The document is a status report to the 95th session of the Working Party on Pollution and Energy, transmitted by the co-chairs of the task force on tyre abrasion in September 2026 and tabled in October. Its title is the whole story: Conclusion of work on UN Regulation on tyre abrasion for C1 tyres, launch of C2 work, outlook for C3 work. Concluded for passenger cars. Launched for vans. An outlook for trucks.

What was actually adopted

UN Regulation No. 186 — still formally bracketed as [186] in the task force’s own numbering at the time of that report — was agreed by the Working Party on Noise and Tyres at an extraordinary session in March 2026, after a failure to reach consensus on test method equivalence at the February session. The compromise was to include both candidate methods in the regulation from the outset. It was then submitted to the World Forum for Harmonization of Vehicle Regulations and formally adopted at WP.29’s 199th session in June 2026.

It carries two stages. Stage 1 requires new tyre type approvals from 30 June 2028 and all type approvals from 30 June 2030, with tyres manufactured before June 2030 permitted to be fitted to a vehicle in use until 30 June 2032. Stage 2 tightens the limits: new type approvals from 30 June 2033, all approvals from 30 June 2035, with extended acceptance of Stage 1 approvals allowed through that date.

Every one of those numbers applies to class C1 tyres — passenger car tyres, in the language of UN Regulation No. 117. The regulation that now governs how fast a car tyre may wear does not yet govern how fast a truck tyre may wear.

How the truck tyre got a date anyway

Not through the UN process. Through Brussels.

Regulation (EU) 2024/1257 — Euro 7 — does not write a tyre abrasion limit. It writes an implementation schedule that reaches into the UN regulations and applies whichever ones exist. The Commission’s transposition status, set out in its EVE-100-12 note of 13 October 2026, is precise about the dates: Euro 7 applies to new heavy-duty vehicle types from 29 May 2028 and to all new heavy-duty vehicles from 29 May 2029, and tyre abrasion under UN R186 applies from 1 July 2028 for C1 class tyres, 1 April 2030 for C2 class tyres and 1 April 2032 for C3 class tyres.

That is the ladder. A passenger car tyre in July 2028, a van tyre twenty-one months later, a truck tyre twenty-four months after that. The European Union has therefore given the heaviest tyre in its vehicle fleet a compliance date of 1 April 2032 — while the UN regulation it is pointing at covers only the lightest class.

The gap is not administrative

The C2 work tells you how hard the C3 work will be. The task force reports that initial C2 testing, using both summer and winter reference tyres, “highlighted that C2 tyres exhibit temperature sensitivity that may differ from that of C1 tyres”, and that the 2026 campaign would focus on confirming the reference tyre strategy and assessing temperature sensitivity and pressure impact.

Read that as a list of unsolved problems, because it is one. A wear test produces a number in millimetres per thousand kilometres; that number depends on the reference tyre chosen, on the surface, on the ambient temperature and on inflation pressure. For a C1 tyre those variables can be controlled tightly enough that two methods — and this regulation carries two — are considered equivalent. A C2 tyre, which carries higher loads at higher pressures and is sold in both summer and winter constructions, already behaves differently enough to reopen the question.

A C3 tyre makes everyone of those problems worse. It is the largest and heaviest tyre in the regulation. It runs in single and dual fitment, which means the same size designation can describe two different contact patches on the same axle. It is designed to be retreaded, which raises a question the C1 regulation never had to answer: whether abrasion performance attaches to the casing, to the tread, or to the pair. And its operating envelope runs from a municipal refuse truck averaging fifteen kilometres an hour to a long-haul tractor holding a hundred.

Why the sequence matters commercially

A compliance obligation with no procedure behind it is not a neutral state of affairs. It redistributes advantage, and it does so in a specific direction.

It removes any possibility of being first. A manufacturer cannot engineer to a test that does not exist, cannot be certified early, and cannot claim compliance as a differentiator in a tender. For an incumbent with a mature compounding platform, that is a gift: it freezes the basis of competition for six years.

It also concentrates power in the method. When C3 testing is finally drafted, the regulation will need a reference tyre, and reference tyres are usually supplied by the manufacturers in the room. The task force’s own history shows how consequential that choice is — the February 2026 deadlock was about method equivalence, and the March compromise was to keep both candidate methods rather than pick a winner. A market in which the reference artefact is selected by a handful of firms is a market in which the cost of compliance is partly decided by competitors.

And it interacts with retreading in a way nobody has yet resolved publicly. Europe’s retreaded share of the truck tyre replacement market fell from 34.2 per cent in 2012 to 20.1 per cent in 2022, and retreaded truck tyre volumes fell from 5.81 million in 2007 to 4.29 million in 2022. If an abrasion limit attaches to the tyre as placed on the market, the retreading industry needs to know whether a retreaded casing is a new placement — and BIPAVER, the European retreading association, spent September 2025 arguing to the Commission that tyre casings should be recognised as raw materials under the proposed Circular Economy Act. An abrasion rule that reached retreads would be the single largest regulatory event in the history of that industry. An abrasion rule that did not would create a two-tier market in which the second life is exempt from the standard applied to the first.

What to watch

The next signal is not the 2032 date. It is the GRPE session at which the C3 work stops being an “outlook” and acquires a mandate, and after that the first appearance of a C3 reference tyre specification. Both will happen years before a truck tyre has to comply, and both will tell you more about who wins this market than any forecast.

Until then, the honest statement is the one the task force made about itself: work concluded on C1, work launched on C2, an outlook on C3. A regulation written for passenger cars, extended by a European vehicle regulation to the heaviest tyre on the road, with the method still to be written.

References

  • UNECE, Status report of TF TA to 95th GRPE session, informal document GRPE-95-59, September/October 2026.
  • Global Automotive Regulations, EVE-100-12: Euro 7 application and UN type-approval equivalence, 13 October 2026.
  • Regulation (EU) 2024/1257 (Euro 7).
  • UN Regulation No. 117, Revision 5 — classes C1, C2 and C3; rolling resistance, wet adhesion and noise.
  • UN Regulation No. 54, Revision 3, Amendment 5 — scope and definitions.
  • UNECE informal document GRBP-78-29, Small group on retreaded tyre regulation split, 2023.
  • European Tyre and Rubber Manufacturers’ Association retreading statistics, cited via AZuR network.
  • BIPAVER statement on the EU Circular Economy Act, September 2025.