Editorial Article
UN Regulation No. 117 Gives the Widest Reinforced Tyre Five More Decibels Than the Narrowest Standard One — and UN Regulation No. 186 Tests That Tyre First
There is a table in UN Regulation No. 117 that tells you what the tyre industry thinks an SUV is. Paragraph 6.1.1 sets the rolling sound limit for class C1 tyres by nominal section width: 70 dB(A) at 185 mm and below, 71 dB(A) over 185 up to 245 mm, 72 dB(A) over 245 up to 275 mm and 74 dB(A) above 275 mm. Then it adds a line: those limits “shall be increased by 1 dB(A) for ‘snow tyre for use in severe snow conditions’, extra load tyres or reinforced tyres, or any combination of these classifications.”
Two variables, and one allowance stacked on top of them. A narrow standard car tyre is permitted 70 dB(A). A wide reinforced tyre on the same class of vehicle is permitted 75. The regulatory gap between the smallest and the largest passenger car tyre is five decibels.
The regulation is not being generous. It is being accurate. The 1 dB(A) is granted because the tyre is carrying more load, and it is granted on the explicit legal definition of what carrying more load means — which is the sentence the whole highway-terrain category actually rests on, and which almost none of its marketing uses.
Paragraph 2.11: the only definition that matters
UN Regulation No. 117 defines a reinforced or extra-load tyre of class C1 as “a tyre structure designed to carry more load at a higher inflation pressure than the load carried by the corresponding standard version tyre at the standard inflation pressure as specified in ISO 4000-1:2010.”
That is the technical content of “highway terrain”. Not the tread pattern, not the compound, not the silica loading, not the acoustic foam. All of those are available on a hatchback tyre and most of them are fitted to one. What an SUV highway-terrain tyre has that the passenger car tyre beside it in the same nominal size does not is a higher load index, a stiffer sidewall and a higher cold pressure.
Everything the category says about itself follows from that. The stiffer sidewall is why the vehicle rides worse than its platform would suggest. The higher pressure is why the contact patch is different. The extra mass and the extra material are why the tyre is dearer and why it wears differently. And the load is why the regulator, having written a noise limit indexed to width, had to write a second line acknowledging that a tyre built this way will be louder.
The industry’s marketing calls this “SUV-tuned”. The regulation calls it reinforced. The second phrase is the one that determines what the product can and cannot be sold as, in every market that recognises UN type approvals.
Why one decibel is not a rounding
The decibel is a logarithmic ratio. One dB(A) is a small change in a quiet room and a substantial one in a product specification, and the industry does not spend money on noise reduction for entertainment. A polyurethane acoustic foam ring bonded inside the inner liner is a real manufacturing step with a real bill attached; tread pitch sequencing designed to spread the spectrum rather than concentrate it costs design cycles and often grip.
Both technologies exist because the buyer of a modern SUV, and particularly the buyer of an electric one, has a specific problem. An internal combustion engine masks tyre noise. Remove it and the dominant cabin noise source becomes the contact patch — a contact patch that, on a vehicle weighing two tonnes and riding on 255-section reinforced tyres, is generating more noise than the equivalent passenger car’s in the first place. So the vehicle gets quieter overall and the tyre becomes the thing you hear.
The result is a market in which quietness is a headline claim on almost every SUV tyre sold, and in which the regulator permits the widest of those tyres five decibels more rolling sound than a supermini’s. Both statements are true at once. There is no contradiction to resolve — only a distinction between what is being optimised and what is being permitted.
Worth noting what the allowance is not. It is not an exemption and it is not a loophole being exploited. Paragraph 2.11 ties the extra decibel to a load-carrying structure defined against an ISO standard, and the limit table ties it to a section width. A manufacturer cannot claim the allowance without meeting the definition. What the regulation has done is accept, in advance and in a table, that the vehicle class the industry is selling hardest will be louder, and has written that acceptance into the approval regime.
Then a third parameter, on a date
On 30 June 2028 the arithmetic changes, because a parameter arrives that is much harder to index to good intentions.
UN Regulation No. 186 on tyre abrasion was agreed at the extraordinary session of the Working Party on Noise and Tyres in March 2026, and the consolidated text went to the World Forum for Harmonization of Vehicle Regulations for formal adoption at its 199th session in June 2026. It is a two-stage regulation with dates that land inside this market’s forecast window:
| Stage | New C1 type approvals | All C1 type approvals | Notes |
|---|---|---|---|
| Stage 1 | 30 June 2028 | 30 June 2030 | Tyres manufactured before June 2030 may be fitted to a vehicle in use until 30 June 2032 |
| Stage 2 | 30 June 2033 | 30 June 2035 | Tighter limits and revised category adjustments; Stage 1 approvals accepted through 30 June 2035 |
Two features of that schedule matter more than the numbers.
C1 comes first. The passenger car tyre — which includes every SUV highway-terrain tyre ever made — is the world’s first tyre class to face a legal abrasion limit. C2 slipped during 2026: the UNECE task force concluded that a formal working document in September 2026 was no longer viable and postponed it to February 2027 after finding that C2 tyres “exhibit temperature sensitivity that may differ from that of C1 tyres”. C3 is further back still, at a brainstorming stage, with a two-day session in Brussels in October 2026 dedicated to finding a simplified test method because the task force acknowledged a “severe complexity and distinct lack of synergies” between the passenger class and heavy truck tyres.
The second stage begins in the terminal year of the forecast. A tyre type approved in 2027 has to meet Stage 1 by June 2028 and will still be on the shelf when Stage 2 tightens in June 2033. There is no window in which a manufacturer can sit this out.
Which brings the two regulations together into a single sentence. The tyre permitted to be the loudest is also the tyre that has the most abrasion to lose, because both are consequences of the same design decision: more load carried on more material at higher pressure. UN Regulation No. 117 accommodated that tyre. UN Regulation No. 186 tests it, first.
The adjustment structure softens this for some products and not others. The limit table is adjusted by tyre group, with cumulative adjustments, and the groups are defined by technical parameter. A low-profile performance tyre — aspect ratio 40 or less, high speed symbol — sits in one group; a highway-terrain tyre at an aspect ratio of 55 to 65, where the sidewall is doing suspension work, sits in another. The premium car tyre report in this segment records the concession written for the low-profile product. The highway-terrain tyre is closer to the standard-load core of the regulation, and further from the allowances.
And a label that will not tell anyone
Here is the part that should interest a commercial reader more than the engineering.
The EU tyre label under Regulation (EU) 2020/740 carries fuel efficiency, wet grip and noise. It does not carry abrasion, and the current revision suggests it will not. The Commission’s proposal of 24 June 2026 — COM(2026) 565 final, amending Regulation (EU) 2017/1369 and Regulation (EU) 2020/740 — is framed around simplification and better use of digital options, not around adding parameters. The Council agreed its position on 6 November 2026, and its mandate specifies more precisely the conditions under which the Commission may update or rescale “the fuel efficiency, wet grip and noise parts of the tyre label” — explicitly those three, and explicitly to address cases where “technological, market or regulatory developments cause a concentration of models in only a few performance classes”.
So the position from 2028 is this: an abrasion limit that determines whether a tyre may be sold at all, delivered through type approval, invisible on the label, in a market where roughly four out of five tyres are bought by a consumer in a fitting bay. The buyer will be able to compare two tyres on rolling resistance to one of seven classes and will have no comparable signal on the parameter that the regulator decided was important enough to legislate.
That has two consequences. The compliance cost is absorbed into the product rather than reflected in a price the customer can compare, which favours whoever can absorb it most cheaply — that is, scale. And the marketing will fill the gap. Expect “long-life” and “abrasion-resistant” claims to proliferate on packaging with no regulatory definition behind them, which is precisely the situation the label exists to prevent for the three parameters it already covers.
What it means for the next eight years
For a tyre maker the message is that the load index has become a liability as well as a price mechanism. Carrying more load justifies a higher price — that is the mechanism documented across this segment, where 52.08 per cent of the highway-terrain market’s USD 64.5 billion of growth to 2033 is price and mix. Carrying more load is also what generates the abrasion the new regulation measures.
Both of those are true, and the manufacturers are behaving as though they know it. Michelin‘s 2025 results record a mix effect of EUR 462 million against a price effect of EUR 365 million, with 18-inch and larger tyres at 68 per cent of MICHELIN-brand passenger car tyre sales. Pirelli closed 2025 with High Value at 79 per cent of sales and car 17-inch-and-below volumes down 11 per cent against a market down 1 per cent. Continental launched the UltraContact UX7 in June 2025 as a road-first SUV tyre, with survey work showing 4 per cent of SUV owners ever leave the tarmac. Bridgestone, Goodyear and Hankook are all selling into the same shift.
For a buyer of tyres, or a buyer of tyre companies, the useful question is not whether the abrasion limit will raise costs — it will — but whether it will finally put a number on the one property the category has never been able to advertise. A tyre that carries more load and loses less material is a genuinely better product. UN Regulation No. 186 is the first instrument that will require anyone to prove it.
The regulation that let the SUV tyre be loud did so honestly. The regulation that follows asks it to last. Between 30 June 2028 and 30 June 2033, the second question becomes the harder one.
Sources
- UNECE, UN Regulation No. 117, Revision 5, 20 March 2025, paragraphs 2.11 and 6.1.1 — R117r5e.pdf
- EUR-Lex, UN Regulation No. 117, Official Journal, 7 August 2025 — 2025/1453
- UNECE GRPE, Status report of the Task Force on Tyre Abrasion, February–October 2026 — GRPE-95-59e.pdf
- EUR-Lex, COM(2026) 565 final, 24 June 2026 — eur-lex.europa.eu
- Council of the European Union, “Council agrees position to simplify energy and tyre labelling”, 6 November 2026 — consilium.europa.eu
- Michelin, financial information at 31 December 2025 — michelin.com
- Pirelli & C., review of preliminary results to 31 December 2025, 25 February 2026 — press.pirelli.com
- GoAuto, “Research unveils soft-road SUV truth”, 27 June 2025 — goauto.com.au
- Pheonix Research, Global SUV Highway-Terrain (HT) Tyres Market, 2026–2033
Frequently Asked Questions
What are the current UN Regulation No. 117 C1 rolling sound limits?
Paragraph 6.1.1 of UN Regulation No. 117 sets C1 rolling sound at 70 dB(A) at 185 mm nominal section width and below, 71 dB(A) over 185 up to 245 mm, 72 dB(A) over 245 up to 275 mm and 74 dB(A) above 275 mm, and increases every limit by 1 dB(A) for extra-load or reinforced construction. The widest reinforced tyre is therefore permitted 75 dB(A) against 70 dB(A) for the narrowest standard one.
Why is a reinforced tyre allowed an extra decibel?
Because the tyre carries more load at a higher inflation pressure than the standard version of the same size, which is the definition in paragraph 2.11, and the regulator indexed the limit to the two variables that follow from that: nominal section width and load. The allowance is written into the table rather than granted case by case, so a manufacturer cannot claim it without meeting the definition.
When does UN Regulation No. 186 on tyre abrasion take effect?
Stage 1 requires new C1 type approvals to comply from 30 June 2028 and all C1 approvals from 30 June 2030, with tyres manufactured before June 2030 permitted on a vehicle in use until 30 June 2032. Stage 2 brings tighter limits and revised category adjustments, with new C1 approvals required from 30 June 2033 and all approvals from 30 June 2035. C1 tyres are the first class in scope; C2 work slipped to a February 2027 working document and C3 remains at method-development stage.
Will the abrasion limit appear on the EU tyre label?
No. The EU tyre label under Regulation (EU) 2020/740 carries fuel efficiency, wet grip and noise, and the revision proposed in COM(2026) 565 final of 24 June 2026 is framed around simplification and digital access, with the Council's 6 November 2026 mandate covering the rescaling of those same three parameters. The abrasion limit will operate as a type-approval gate that the end buyer never sees.
